Heavy Equipment Paint

Heavy Equipment Paint

Asparagus Polyurea Light Grey Fast Drying Anticorrosive Primer
Chat Now

Product Details

DESCRIPTION: PH9503-111

High Solid, Rapid‐Drying coating, with excellent adhesion to sand blasting steel.Can normally curing in ‐10℃. No baking,save energy consumption. Apply vocs 250 g / L and meets the green coating standard.

FEATURES:

GENERIC TYPE:

Composed of polyaspartic   polyurea resin and anticorrosive pigments and fillers additives.

RECOMMENDED USES:

Particularly recommended for   assembly line painting of construction machinery.

NOT RECOMMENDED:

Isocyanate of polyaspartic   polyurea is sensitive to water and moisture, which will lead to shorten of   pot life.

WEATHERING:

Topcoat is required.

SUBSTRATES:

Blasted Steel as recommended.   Good compatibility with epoxy and acrylic polyurethane system.

COLORS:

Grey.

GLOSS:

Semi‐Gloss.

CHEMICAL RESISTANCE GUIDE:

 

Immersion

Splash &spillage

Fumes

Acids:

Good

Good

Excellent

Alkalies:

Good

Good

Excellent

Solvents:

Fair

Excellent

Excellent

Salt water:

Good

Excellent

Excellent

Fresh water:

Good

Excellent

Excellent

TEMPERATURE RESISTANCE:

Temperature

Continuous:

Non‐ Continuous:

Dry

60ºC

70ºC

Submerge

40ºC

55ºC

SOLIDS CONTENT: 80± 2% by volume.

 

Filmthickness per coat: μm

Theoretical coverage: m2 / l

 

Dry

Wet

 

1

50‐100

63‐125

16‐8.0

2

80

100

10.0

1、Recommended DFT.

2、Standard.

APPLICATION INSTRUCTIONS:

SURFACE PREPARATIONS:

Remove any oil or grease with   suitable thinner.

POT LIFE:

10 mins at 20℃ and less at   higher temperature and humidity.

STEEL:

Preferably sandblasting. 30   microns surface roughness is necessary.

SHEL FLIFE:

Party A: 1 ‐ 3 years

Hardener Party B: 9 months

Depends On Storage Condition   ).

MIXING:

Mix separately, then use   two‐component sprayer with

combine ratio A: B = 2:1 by   volume.

PACKING:

12.3L/6.7L

According to customer’s   requirement.

THINNER:

Two‐component sprayer no need   thinner. Thin 5‐15% for air sprayer. If need,Please note to use Thinner   PS1002 Special for polyaspartic polyurea. Epoxy thinners are prohibited.

CLEAN UP: Clean with thinner   PS1002 as soon as possible after spray.

APPLICATION TEMPERATURES: 

 

Material:

Surface:

Normal:

5‐30℃

5‐30℃

Minimum:

‐10℃

‐10℃

Maximum:

60℃

60℃

 

Ambient:

Humidity:

Normal:

5‐30℃

35‐80%

Minimum:

‐10℃

0%

Maximum:

40℃

80%

Do not apply when the surface temperature isless than   3℃above the dew point of the air.

APPLICATION METHODS:

Nozzle:0.012 ‐ 0.015"  Pressure:450‐550kpa

Two‐component sprayer is recommended. When air spray is apply, Please consult our engineer before using.

RECOATING TIME:

*Best intercoat adhesion is obtained when the subsequent coat is applied before the preceding coat has cured. Please recoat not more than Max recoated time, otherwise polish is recommended to ensure adhesion.

NOTE: 

The technical information for our products are based on laboratory tests and practical experience. As the products are often being used under conditions beyond our control, we can only guarantee for the quality of the material itself. The technical information is subject to change without prior notice.

 

Inquiry