Shipping Container Paint

Shipping Container Paint

Product Name : Heavy-duty anti corrosive coating-Grey/Red Model No: 725-H45-ZF101G

Product Details

Product Description

--A two pack epoxy heavy-duty anticorrosive coating and it is characterized by good adhesion and excellent resistance to chemicals, water and corrosion.

--VOC less than 180g/L

Intended Uses

--For use in heavy-duty anticorrosive areas.

--For steel ortidal range zone of concrete stakes heavy-duty anticorrosion.

--For interior circulatory water piles of power plant special strengthening anticorrosion

--For interior wall of steel pipes and concrete of Sewage treatment works, power plants and chemical plants etc. heavy-duty anticorrosion.

--For works of tap water and water anticorrosion

Product Information

Volume Solids

80%±2%

Finish/Sheen

Not applicable

Typical Film Thickness

500 microns dry530 microns wet

Theoretical Coverage

1.9m2/L at typical film thickness

Mix Ratio

3.4:1volume7:1(mass)

Method of Application

Airless Spray

Not recommended

Air Spray

Not recommended

Scratch

Recommended

Thinner

Not recommended

Cleaner

HX-501

Induction Period

Not necessary

Drying Information

 

         5

15

25

35

Touch Dry

4h

2h

1h

30min

Hard Dry

36h

34h

20h

16h

Pot Life

1h

45min

30min

20min

Overcoating Data                                                               Substrate Temperature

Overcoated by  

5

15

    25

35

Min Max

Min Max

  Min Max

Min Max

725-H45-ZF101G

     48h 14d

    36h 10d

           16h 7d

             10h 5d

 

 

Storage

Store in cool and dry conditions. Well ventilate. Keep away from hot and fire. Shelf Life: 12 months minimum at 25. Subject to re-inspection thereafter

Pack Size

              Part A

30kg/15.5L in 20L container

 

              Part B

4.3kg/4.5L in 6L container

Flash Point

Part A

Greater than 31

 

              Part B

Greater than 29

 

        Mixed paint

Greater than 31

Systems and

Compatibility

Consult your Sunrui Representative for the systems best suited for the surfaces to be protected.

Surface Preparation

All surfaces to be coated should be clean, dry and free from contamination.

Abrasive Blast Cleaning for steel

Abrasive blast clean to Sa2½GB/T 8923.1-2011. If oxidation has occurred between blasting and application of 725-H45-ZF101G, the surface should be reblasted to the specified visual standard.

Surface defects revealed by the blast cleaning process should be ground. Filled, ortreated in the appropriate manner.

Concrete

Remove loose powder of the cement, attached organisms, mud, oil or grease and other foreign matter thoroughly.

The surface can be abrade by blasting or using power tool to remove loose powder, attached organisms, mud etc. and oil can be cleaned by scour.

Repair

steel

The areas to be repaired should be cleaned to St3GB/T 8923.1-2011by  mechanical method or higher level of surface prepared to Sa2.5GB/T 8923.1-2011by abrasive blasting. Abrade the area immediately surrounding the repair to provide a key for subsequent coating application. Overlap areas should be kept to a minimum.

concrete

The areas to be repaired should be remove loose powder of the cement, attached organisms, mud, oil or grease and other foreign matter thoroughly. Abrade the area immediately surrounding the repair to provide a key for subsequent coating application. Overlap areas should be kept to a minimum.

 

 

 

Limitations

Apply in good weather. Temperature of the surface to be coated must be least 3 above the dew point when the is lower than 85%.

In common with all epoxy base coatings, 725-H45-ZF101G will exhibit chalking of the firm on UV exposure.

The dry time and overcoating interval may change according to the environment factors.

Avoiding absorb the solvent steam and paint steam for long time. Skin and eyes must avoid contacting the paint. Pay attention to ventilate and fireproof when applying.

 

 


Duty statement:The data in the sheet base on the information from the laboratory and practice. The applica tion may exceed the control, so we only ensure our product quality. We own the right of the data sheet modification without informing.


Send Inquiry